How two Blickfeld Qb2 sensors enable live barge load measurement for partner Ayavex Solutions
Overview
At a barge loading facility on the Fraser River in British Columbia, Canada, woodchips are loaded by conveyor and chute into barges of around 60 × 15 m for shipment by water – typically one barge a day and up to five a week, or around 200 loads a year per loading station.
To measure each load while it was being filled, the facility used ScanBarge, a barge load measurement solution developed by Blickfeld partner Ayavex Solutions of Vancouver. Blickfeld provides the sensing: two Qb2 LiDAR sensors capture the 3D data on which Ayavex’s application is built.
Challenge
For a barge loading operation, the goal of every loading cycle is simple: bring the barge to its target level before it leaves the dock. Achieving this, however, depends on information that is rarely available while loading is under way. Traditionally, the load is measured by hand: a surveyor climbs to the top of the heap and takes up to 40 survey points to estimate the volume on board. The method is time-consuming and potentially unsafe, and its result comes too late to act on – an underfilled barge is identified only a day later, after it has left the dock.
However, a single measurement has a further weakness: the load does not stay the same. Woodchips that fall from a chute come to rest loosely, with air trapped between them, and continue to settle for hours after loading has stopped. The result: the time of the measurement determines what it reports, and two correct measurements of the same barge can differ, leaving room for discussion between buyer and seller.
Underfilling has a direct cost. At Ayavex’s estimate of CAD 20,000 (about EUR 13,000) per round trip, every percentage point of capacity that sails empty is worth around CAD 200 (about EUR 125) of unused tow.
Solution
ScanBarge is based on two Blickfeld Qb2 sensors, mounted on masts at the top of the loading conveyor around 16 m above the deck. One faces each end of the barge, and with a field of view of 90° × 50° each, together they cover the entire hull – no equipment is required on the barge itself. The masts allow the sensors to be fitted and adjusted without a lift, and each sensor needs only a single Power over Ethernet cable. Beyond the standard IP67 housing and Blickfeld’s weather protection roof, no special protection was needed at the open berth. Once the masts, power and network are in place, installing the sensors takes up to one hour. The system was deployed at the berth for a three-month evaluation period, from May to August 2026.
Qb2 sensors on the loading structure above the berth
The Qb2 can process 3D data directly on the sensor, but it also gives partners access to its raw point clouds via open interfaces, including C++ and Python client libraries and ROS drivers. One significant advantage for partners: Ayavex takes the point clouds through the Qb2 API and processes them in its own ScanBarge software, so the same sensor serves as the platform for a specialised application.
Each scan produces a complete 3D surface of the load, which ScanBarge converts into a live volume reading and a map of the zones that are still low. The operator sees both on screen while the chute is running and can direct material to where it is still needed.
In addition, the sensors continue to scan after loading has stopped. Instead of a single snapshot, the operator thus receives a continuous record of how the load changes over the following hours.
Results
The added value of the solution became evident during loading itself. Before ScanBarge, the crew loaded by eye, and the fill figure came from the manual survey only after the barge had left. With ScanBarge, the volume and the zones still low were on screen while the chute was running, so the operator could see how full the barge was while there was still time to act.
Across Ayavex’s measurements to date, the volumes determined by ScanBarge agreed with the certified manual survey to within 0.8% to 3.7%.
The room for improvement is clear: on four barges, the certified survey recorded 94.4% to 96.7% of rated capacity, so between 3% and 6% of the space sailed empty.
The operators view during loading
At an estimated CAD 20,000 per round trip, the empty space was worth around CAD 650–1,100 (about EUR 400–700) per sailing, or roughly CAD 130,000–225,000 (about EUR 85,000–140,000) a year at 200 loads, by Ayavex’s estimate. How much of it the crew recovers with live measurement is the next thing Ayavex will measure. The same live reading also tells the loader when the barge has reached its target, so it is not overloaded in the first place.
Continuous measurement also revealed something that a single survey cannot capture: the load kept settling for hours after the chute stopped. On one barge, the surface dropped by around 2% of the chip depth overnight, although nothing was added or removed. Ayavex describes the measurement in detail in its field notes.
Detecting this requires measurement quality, not just coverage. From 16 m above the deck, the Qb2 sensors resolved an average surface drop of just 8 cm. The pattern of the drop confirms that the change in the load was real rather than a drift in the measurement, and the sensors maintained a stable measurement throughout the night.
For the operators, this has two consequences. A measurement taken as the chute stops and one taken the following morning can both be correct and still differ, so a continuous record showing when each figure was taken gives buyer and seller the same view of the load. And the space that settling opens up becomes visible on screen, where it could be topped up while the barge is still at the dock.
We needed a sensor that would give us clean 3D data from 16 m above an open berth, day after day, and let us build our own application on top. The Qb2 does that: its open interfaces meant we could focus on ScanBarge instead of the sensing, and the measurement is stable enough to show a few centimetres of settling overnight.
Tsolmon Munkhchuluun
CEO, Ayavex Solutions
Outlook
The settlement measurement covered one load on one barge, in summer, with a single chip supply. Since wood species, moisture, chip size and time at the dock all influence how much a load settles, Ayavex is now adding further loads, with the goal of building a settlement curve rather than a single data point.
You are currently viewing a placeholder content from Vimeo. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.
You are currently viewing a placeholder content from YouTube. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.
You are currently viewing a placeholder content from Facebook. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.
You are currently viewing a placeholder content from Instagram. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.
You are currently viewing a placeholder content from Google Maps. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.
You are currently viewing a placeholder content from Google Maps. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.
You are currently viewing a placeholder content from Mapbox. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.
You are currently viewing a placeholder content from OpenStreetMap. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.
You are currently viewing a placeholder content from X. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.